Damn Vape Nitrous RDTA atomizer

Damn Vape Nitrous RDTA atomizer

Damn Vape Nitrous RDTA

The Nitrous Damn Vape RDTA, with its 36 mm height and 24 mm diameter, has a capacity of 3 ml.

Precise honeycomb airflow

The design is fairly classic, except for the flashy version for a fun touch. But beyond that, the machining is perfectly executed. The spray bell is squircle-shaped: round contours with two straight sides. This particular shape, with its honeycomb airflow, allows you to get as close as possible to the coils, speeding up cooling and optimising the flavour experience.

Nitrous atomizer disassembled

The 810 drip tip is designed for a very airy draw. You can also insert a narrower 510 drip tip for a tighter draw using the 810 to 510 adaptor included in the kit. The removable top cap allows you to remove the airflow ring and, if necessary, clean the entire device.

Single and double coil mounting tray

An attractive mounting plate under the bell accommodates either a single coil (max. diameter 5 mm) or a double coil (max. diameter 3 mm). The coils are tightened from the side.

It's easy to assemble because the tray offers plenty of space. 4 metal braids feed the cotton in your assembly. A hole allows you to introduce the 3 ml of liquid into the removable reservoir.

The metal braids can be cleaned and replaced if necessary (4 replacement braids are included in your kit). The Nitrous RDTA comes with a Pin 510 BF so you can fill your tank directly from your favourite BF box mod.

Damn Vape Nitrous RDTA complete kit

Calumette's review: An excellent RDTA, small in size, easy to use for long hours of vaping. It's a high-performance, versatile device that, thanks to the BF pin, can be used with a Bottom Feeder box.

E-liquid not included: Complete your purchase with e-liquid.
For a first purchase, we advise you to test several different liquids, for example at least one Classic flavour and at least one fruity flavour.

Advantages

• Single or double coil assembly
• BF compatible
• 3 ml tank
• Fully removable

Kit contents

• 1 Damn Vape Nitrous RDTA atomizer
• 1 O-rings kit
• 1 multi-purpose screwdriver, flat, cross-head and Allen-head
• 4 replacement screws
• 1 replacement pyrex
• 1 coil template
• 1 810 to 510 drip tip adaptor
• 1 510 drip tip
• 4 replacement braids
• 1 BF pin
• 1 user manual

Specifications

• Length: 3.6 cm
• Diameter: 2.4 cm
• Weight : 34 g
• Capacity: 3 ml
• 510 screw thread, BF compatible
• 810 drip tip type
• Assembly: double coil or single coil
• Stainless steel spray bell
• Compatible with coils: rebuildable coil
• Inhalation type: direct
• vapor type: airy
• vapor: cold to hot
• Percentage of VG in liquid for optimum use: ≤ 90% Vegetable Glycerin
• Level: expert

Use

- Placing your coils:
Remove the base of the atomizer to access the base of the tray. Unscrew the tray screws using the screwdriver supplied.

Cut the coil wires using the template supplied. Place your coils on the tray and tighten the screws. Carefully cut a piece of cotton about 0.5 cm long and roll it up to fit in the centre of the coil.

Redirect the wicks on either side of the coils and trim the excess so that the cotton does not protrude from the tray. Soak your cotton well before closing your atomizer/dripper. Now all you have to do is fill it up and vape!

We advise you to check the resistance in ohms of each of your coils with an ohm meter. A too low coil or a short circuit can seriously damage your equipment.

advice

- We suggest you try several different wires and cottons to find your ideal vape. Bear in mind that the thinner the wire, the greater the resistance, and vice versa.