Hellvape Dead Rabbit Pro RDA dripper

Hellvape Dead Rabbit Pro RDA dripper

Hellvape Dead Rabbit Pro Dripper

Following in the footsteps of the Dead Rabbit, Hellvape presents the Pro version of its famous RDA. Compact and with a diameter of 24 mm, it works with double coils and offers a host of advantages. As with the rest of the range, the product has been crafted to a very high standard.

810 drip tip and first airflow ring removed from the dripper

The atomisation bell with its short 810 drip tip gives a very airy direct draw.

From left to right: airflow at the bottom of the coil, airflow above the coil and dual-flow airflow.

Two airflow rings have been introduced:

- The first draws in a large quantity of air under the coils to cool and stir your vapor cloud.

- The second adds air directly into the atomiser bell above the coils.

It's all a matter of adjusting the settings to get the best out of your flavours and your clouds of vapor.

Dead Rabbit 3 dripper, fully disassembled

The dripper comes with a different-coloured top ring and another drip tip for customising your device.

Dual-coil mounting tray

A large mounting plate easily accommodates 2 coils (even large-diameter coils). The air can be directed under the coil, above it or in double flow, so this dripper offers great vape comfort, excellent flavour reproduction and superb clouds of vapor.

Mounting plate without and with double coils

Located on the side, the clamping screws ensure that the coils remain firmly attached to the tray.

Your kit also includes a 510 BF pin. So you can mount your dripper on your favourite Bottom Feeder box.

Hellvape Dead Rabbit Pro complete kit

Calumette's review: The double airflow really makes a difference compared to other drippers on the market. It cools the vapor and guarantees excellent flavour reproduction.

E-liquid not included: Complete your purchase with e-liquid.
For a first purchase, we advise you to test several different liquids, for example at least one Classic flavour and at least one fruity flavour.

Advantages

• Dual-coil assembly
• BF compatible
• Dual airflow
• Excellent flavour reproduction

Kit contents

• 1 HellVape Dead Rabbit Pro RDA atomizer
• 1 O-rings kit
• 1 set of Allen keys
• 1 flathead screwdriver
• 4 replacement screws
• 2 cotton wicks
• 2 Fused Clapton Ni80 0.37 ohm coils
• 1 BF pin
• 1 user manual

Specifications

• Length : 2.6 cm
• Diameter : 2.4 cm
• Weight: 35 g
• Capacity: no capacity on a dripper
• BF-compatible 510 screw thread
• 810 drip tip type
• Assembly: double coil
• Stainless steel atomisation bell
• Compatible with coils: rebuildable coil
• Inhalation type: direct
• vapor type: airy
• vapor: cold to hot
• Percentage of VG in liquid for optimum use: ≤ 90% Vegetable Glycerin
• Level: expert

Use

- Placing your coils:
Unscrew the base of the atomizer to access the base of the tray. Unscrew the tray screws using the screwdriver supplied.

Cut the coil wires using the template supplied. Place your coils on the tray and tighten the screws. Carefully cut a piece of cotton about 0.5 cm long and roll it up to fit in the centre of the coil.

Redirect the wicks on either side of the coils and trim the excess so that the cotton does not protrude from the tray. Soak your cotton well before closing your atomizer/dripper. Now all you have to do is fill it up and vape!

We advise you to check the resistance in ohms of each of your coils with an ohm meter. A too low coil or a short circuit can seriously damage your equipment.

Advice

- We suggest you try several different wires and cottons to find your ideal vape. Bear in mind that the thinner the wire, the higher the resistance and vice versa.